Showing posts with label ergomo. Show all posts
Showing posts with label ergomo. Show all posts

Monday, November 10, 2008

Method for Calibrating Ergomo Power Meter using Computrainer


This describes how to calibrate an Ergomo Power Meter using a Lab Computrainer.

It is hard to verify that the Computrainer is more or less accurate than any particular Ergomo. But using a simple ramp test we can confirm two things. First how the two devices diverge. And second get a reasonable idea on how reproducible the two report.

Finally, if you have more than one Power Meter for different bikes, then using this method, you can re-calibrate them so that they agree. And that they agree with your trainer (assuming you are using a CT for your trainer.) 

I have three different Ergomo BB's (road, TT and track) and train indoors on the CT. Prior to developing this procedure I was getting fairly divergent numbers. Large enough to make a difference to CTL/ATL/TSB numbers in WKO+. Getting them all to agree was the reason for doing this.

1. Setup

Setup is simple. You just need to get your bike with PM installed and setup on the Computrainer. 

Tire pressure should be about 110PSI. 

The roller on the CT should be cleaned.

Do the initial re-calibrate for the CT. Typically I try for about 3.00 at this point. Adjust the roller appropriately.

2. Warm up

Do a simple warmup. About 100-200 watts. Do a re-calibrate every 3-4 minutes. If the number falls below 2.5, increase the roller clamp pressure.

Once you have a stable number over 2.5, seen in two or more re-calibrations a couple of minutes apart proceed to step 3.


3. Ramp Test

Start the coaching software, using the following erg file:

[COURSE HEADER]
VERSION = 2
UNITS = ENGLISH
DESCRIPTION = Power Meter Calibration 60w per min
FILE NAME = PowerMeterCalibration20.erg
MINUTES     WATTS
[END COURSE HEADER]
[COURSE DATA]
0.0     100
8.0    580
[END COURSE DATA]
This is a simple ramp test, starting at 100W and increasing 60W every minute. 


4. Test

To ensure that the CT didn't cool down, do another few minutes of warmup with the coaching software running, the test loaded, but not started.

Then start the test, ensure that your Power Meter is also recording.

Try to maintain a fairly constant and comfortable cadence. If possible over 80RPM. 

The first few minutes are easy... the last minute is hell... hang in as long as you can.


5. Results

Copy the CDF.txt file produced from the Coaching file into WKO+. Also import your PM data.

Inspect both files and cut out the parts that do not pertain to the test. You should end up with about 4-6 minutes of data from both the CT and your PM.

Use the Export facility to save these into a CSV file.

6. Excel

Open the two CSV files in Excel, and also create a new empty workbook. Cut and paste the Minutes and Watts columns from the CT and PM CSV files into the workbook. You can use Excel tools to compare your results.


7. Sample one - Soloist Ergomo with K-factor 184

This is from a Soloist with Ergomo BB and the factory K-Factor setting.

The two time series are plotted as an X/Y scatter plot (as lines) with trendlines added. Finally a difference column was added and plotted.  

This shows that there is a substantial difference, with the Ergomo reading much higher. The difference does not quite scale linearly. It increases slightly as can be seen in the Diff plot (which uses the right axis).


8. Sample two- Soloist Ergomo with K-factor 164

This test is for the same bike with the K-factor adjusted down from 184 to 164. 

Note that while not an exact match, it is reasonably close now.  

The Diff line is still not exactly linear and does show that the Ergomo is more variable (again Diff is show using right axis.)


9. Conclusions

As can be seen, it is reasonably easy to get the Ergomo to match the Computrainer by adjusting the K-Factor appropriately. 

While this does not guarantee accuracy, it does provide a way to ensure that multiple devices are all setup to produce similiar results.

The (presumably) best results for this procedure would be with a reasonably new Lab Computrainer. But it is possible that acceptable results could be obtained with the non Lab version or possibly a Tacx or other trainer that can control the watts in "Erg" mode (i.e. set the load level absolutely, regardless of tire speed, rider cadence etc.) and can record the results.



Sunday, November 9, 2008

New FTP!

Good news bad news...


After doing a VO2Max test a few weeks back I decided that my Ergomo's where reading too high. At least WRT to the Computrainer at the Lab.. So I repeated the ramp test here on my Computrainer, using my P2c with Ergomo. And then compared the results... 

It showed that P2C Ergomo was reading perhaps 20% to high in the "interesting" range (200-350). 

So I replicated the test using the Soloist with it's Ergomo. Similiar, although possibly not quite 20%. 

So off to the track and drag home the track bike and test with it... There the numbers matched reasonably well, although possibly slightly low.

So mea culpa... I now have a good explanation of why the numbers on the TT bike where slightly higher than the road bike. And why both the those where higher than the CT or Track... 

I had assumed, since the number from the two road bikes (Soloist and P2c) where reasonably similiar, that they where fairly trust worthy.. Apparantly a bad assumption.

I'll do a separate post showing some sample results and explaining the test regime. The results are that I have reset the K-Factor's on each of the Ergomo's to adjust them down (or up) as appropriate:

  1. Track 181 -> 182
  2. Soloist 184 -> 165
  3. P2C 196 -> 164
This assumes of course that the Lab Computrainer I have is accurate. Not necessarily a great assumption. But the main excercise is not so much absolute accuracy as having the all of the devices I use provide equivalant data. I'll also point out that a) it is a Lab CT, b) it's reasonably new and lightly used (<2years)>

The above adjustments should mean an FTP in the new regime of about 280. I"ll need to do some testing to confirm that one way or another.

The other problem is that CTL/ATL/TSB for the last few months (since I've been back at the track) are off significantly. If the track bike was under reporting as compared to the FTP from testing on the road, then TSS points computed and therefore CTL/ATL/TSB are too low. Especically true on the track where we see short and intense efforts. 

Going forward we'll be ok. But it takes some work to get the past few months corrected. The simplest approach is to simply use the "new zones" feature to set a new FTP prior to each weeks track or road. Moving it up and down to match. The end result was to move current CTL from about 70 to 79.

Today was the first day out on the re-calibrated Soloist... Got rained on doing Ford Road at L2/L3. The legs where a bit tired from doing the (5) ramp tests yestered (start at 100 and ramp at 60w/minute until failure, about 5 minutes...) 





Friday, April 11, 2008

New Ergomo software available

New version of the software ergoRacer 3.0

With the enhanced version of our software ergoRacer 3.0 you will find another great software on our website www.ergomo.net as a free download.

Beside the previous languages German and English the new software is now as well available in Spanish. Furthermore we adapt the interval mode and the function to have multiple downloads, which are working now without any problems. All manual arranged petitions in the new version of the software will be stored, also after a software update, and must not be reentered.

Download the latest ergomo® software (Version PN20080306) now from our webpage.

Thursday, October 11, 2007

Ergomo Display - updated

Robert Jordan has a nice overview of how he is changing his ergomo display here.

And I previously blogged about it here. But realized that after using the new display I ended up changing it again, and that I've been happy with that for several months now. So I thought I would update here.

The Ergomo has two display screens accessed by the top orange button.

Note that the middle line containing watts and speed is the same on both screens. This is the most important (usually) information, and I find it slightly easier to find and read in the middle line.

I view the main display as my "working" screen, showing:

cadence, grade,
watts, speed,
average watts, average speed,
trip time, trip distance
The main display is what I normally use when racing or time trialling. It gives me the current conditions (grade, speed, watts, cadence etc.)



And the alternate display is the "training screen":

heart rate, total climbing
watts, speed
normalized watts, TSS
trip time, clock time



The alternate display is what I spend most time in when training... So I can monitor heart rate, work done (TSS), amount climbed etc. Also shows wall clock time so I know when I'm late for dinner.

Actually having wall clock time is also important for getting to the start line for time trials... just make sure that you keep it accurate and check with the official starter to see if his "official" time is different.

Wednesday, October 3, 2007

MacGyver Ergomo Mount



My impression over the past few track sessions was that my power was a little low. So I did some preliminary bike fit changes. This involved swapping the stem which also meant swapping the bars, getting new bar tape etc (I had the stem and bars, easier to swap than to get a new stem...) to move the bars out and up.

Of course this meant that I got to the track tonight without a mount for the Ergomo...





So we now present the MacGyver Ergomo Bike mount.









Did three sessions, endurance/tempo paced. just getting the track legs back.

Entire workout (218 watts):

Duration: 1:35:41 (2:52:38)
Work: 1252 kJ
TSS: 92.5 (intensity factor 0.762)
Norm Power: 244
VI: 1.12
Distance: 56.802 km
Elevation Gain: 212 m
Elevation Loss: 85 m
Grade: 0.2 % (127 m)
Min Max Avg
Power: 0 729 218 watts
Heart rate: 0 0 0 bpm
Cadence: 24 121 87 rpm
Speed: 0 51.5 35.6 kph
Pace 1:10 0:00 1:41 min/km
Altitude: 32 163 104 m
Crank Torque: 0 70.7 23.4 N-m
Temperature: 17 21 19.4 Celsius

Wednesday, August 22, 2007

Wheel Magnet on Hub



I found a good way to get the wheel magnet mounted so that it is out of the air stream and has reduced rotational mass.

The speed sensor (for Ergomo) was just long enough that I could tuck it inside of the chain stay keeping it out of the main air flow. Then simply glue the magnet on to the hub body

This works well on a disc wheel as well.

Magnets are available at reasonable cost (30-50 for $8.95, depending on what size you want, plus shipping):

www.rare-earth-magnets.com


Monday, July 9, 2007

Ergomo programable display

Ergomo released their new user display program today. It allows for customizing the default and alternate displays. It can now display to eight items on each page.

I keep power (watts), speed and stop watch on both displays, in the same position.


The default page shows the power related items like average and NP watts, TSS and distance.





The alternate page shows grade, meters climbed, heart rate, cadence and clock.